[1006] ~%sudo smartctl -a /dev/disk1 11:06AM smartctl 6.1 2013-03-16 r3800 [x86_64-apple-darwin12.3.0] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org SATSMARTLibFactory called SATSMARTClient::alloc called SATSMARTClient : QueryInterface called kIOCFPlugInInterfaceID requested SATSMARTClient::Probe called SATSMARTClient::Probe called 0 SATSMARTClient : Start SATSMARTClient : IOServiceOpen status = 0x00000000, connection = 5651 SATSMARTClient : QueryInterface called kIOATASMARTInterfaceID requested SATSMARTClient::GetATAIdentifyData 0x200 SATSMARTClient::GetATAIdentifyData status = 0 === START OF INFORMATION SECTION === Model Family: Hitachi/HGST Travelstar 5K750 Device Model: Hitachi HTS547550A9E384 Serial Number: J2160051DDYGSD LU WWN Device Id: 5 000cca 63cd3fa9b Firmware Version: JE3OA60A User Capacity: 500,107,862,016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS T13/1699-D revision 6 SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Sun Aug 11 11:13:57 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled SATSMARTClient::SMARTReadData called SATSMARTClient::SMARTReadData status = 0 SATSMARTClient::SMARTReadDataThresholds called SATSMARTClient::SMARTReadDataThresholds status = 0 === START OF READ SMART DATA SECTION === SATSMARTClient::SMARTReturnStatus called exceededCondition = 0 SATSMARTClient::SMARTReturnStatus status = 0 outputCnt = 1 SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 45) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 135) minutes. SCT capabilities: (0x003d) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 161 161 033 Pre-fail Always - 1 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 565 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0 9 Power_On_Hours 0x0012 076 076 000 Old_age Always - 10730 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 18 191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 6325 194 Temperature_Celsius 0x0002 181 181 000 Old_age Always - 33 (Min/Max 18/44) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 405 223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0 SATSMARTClient::SMARTReadLogAtAddress called SATSMARTClient::SMARTReadLogAtAddress address = 0 SATSMARTClient::SMARTReadLogAtAddress status = 0x0 SATSMARTClient::SMARTReadLogAtAddress called SATSMARTClient::SMARTReadLogAtAddress address = 1 SATSMARTClient::SMARTReadLogAtAddress status = 0x0 SMART Error Log Version: 1 ATA Error Count: 405 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 405 occurred at disk power-on lifetime: 9890 hours (412 days + 2 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 80 88 2f 4f 06 Error: ICRC, ABRT 128 sectors at LBA = 0x064f2f88 = 105852808 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 f0 18 2f 4f 40 00 2d+23:17:41.575 WRITE DMA EXT 35 00 f0 28 2e 4f 40 00 2d+23:17:41.571 WRITE DMA EXT 35 00 f0 38 2d 4f 40 00 2d+23:17:41.566 WRITE DMA EXT 35 00 f0 48 2c 4f 40 00 2d+23:17:41.562 WRITE DMA EXT 35 00 f0 58 2b 4f 40 00 2d+23:17:41.558 WRITE DMA EXT Error 404 occurred at disk power-on lifetime: 9284 hours (386 days + 20 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 a0 e0 a2 07 0d Error: ICRC, ABRT 160 sectors at LBA = 0x0d07a2e0 = 218604256 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 f0 90 a2 07 40 00 7d+08:44:39.715 WRITE DMA EXT 35 00 f0 a0 a1 07 40 00 7d+08:44:39.708 WRITE DMA EXT 35 00 f0 b0 a0 07 40 00 7d+08:44:39.703 WRITE DMA EXT 35 00 f0 c0 9f 07 40 00 7d+08:44:39.697 WRITE DMA EXT 35 00 f0 d0 9e 07 40 00 7d+08:44:39.693 WRITE DMA EXT Error 403 occurred at disk power-on lifetime: 9189 hours (382 days + 21 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 a0 78 0f 80 0d Error: ICRC, ABRT 160 sectors at LBA = 0x0d800f78 = 226496376 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 f0 28 0f 80 40 00 3d+10:02:28.331 WRITE DMA EXT 35 00 f0 18 10 80 40 00 3d+10:02:28.327 WRITE DMA EXT 35 00 f0 08 11 80 40 00 3d+10:02:28.322 WRITE DMA EXT 35 00 f0 f8 11 80 40 00 3d+10:02:28.318 WRITE DMA EXT 35 00 f0 e8 12 80 40 00 3d+10:02:28.314 WRITE DMA EXT Error 402 occurred at disk power-on lifetime: 8887 hours (370 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 40 e8 29 d1 05 Error: ICRC, ABRT 64 sectors at LBA = 0x05d129e8 = 97593832 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 f0 38 29 d1 40 00 2d+02:34:00.896 WRITE DMA EXT 35 00 10 08 24 47 40 00 2d+02:34:00.862 WRITE DMA EXT 35 00 f0 48 28 d1 40 00 2d+02:34:00.817 WRITE DMA EXT 35 00 f0 58 27 d1 40 00 2d+02:34:00.789 WRITE DMA EXT 35 00 f0 68 26 d1 40 00 2d+02:34:00.773 WRITE DMA EXT Error 401 occurred at disk power-on lifetime: 8793 hours (366 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 a0 d0 55 05 0d Error: ICRC, ABRT 160 sectors at LBA = 0x0d0555d0 = 218453456 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 35 00 f0 80 55 05 40 00 6d+07:12:35.870 WRITE DMA EXT 35 00 f0 90 54 05 40 00 6d+07:12:35.865 WRITE DMA EXT 35 00 f0 a0 53 05 40 00 6d+07:12:35.861 WRITE DMA EXT 35 00 f0 b0 52 05 40 00 6d+07:12:35.845 WRITE DMA EXT 35 00 f0 c0 51 05 40 00 6d+07:12:35.841 WRITE DMA EXT SATSMARTClient::SMARTReadLogAtAddress called SATSMARTClient::SMARTReadLogAtAddress address = 6 SATSMARTClient::SMARTReadLogAtAddress status = 0x0 SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SATSMARTClient::SMARTReadLogAtAddress called SATSMARTClient::SMARTReadLogAtAddress address = 9 SATSMARTClient::SMARTReadLogAtAddress status = 0x0 SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SATSMARTClient : Stop SATSMARTClient : IOServiceClose connection = 5651